Samsung Dishwasher error Codes and solutions from Freedom Appliances

Samsung dishwashers are known for their efficiency, design, and the advanced technology they bring to modern kitchens. However, like any sophisticated appliance, they may occasionally run into issues, signaled by specific error codes displayed on the machine. Understanding these error codes is essential for troubleshooting and ensuring your dishwasher continues to operate smoothly. This article will provide an overview of common Samsung dishwasher error codes, what they signify, and potential solutions to address them.

1. Error Code 5E (SE)

This error indicates a drainage problem. It usually appears when the dishwasher is unable to drain water out. This could be due to a clogged filter, a blocked drain hose, or an issue with the drain pump. To resolve this, check and clean the filter and ensure the drain hose is not kinked or obstructed. If the problem persists, the drain pump may need inspection or replacement.

2. Error Code 4E

The 4E error code signifies that the dishwasher is having trouble filling with water. This could be due to a closed water supply valve, a kinked water supply hose, or a problem with the water inlet valve. Ensure the water supply valve is fully open, the hose is not kinked, and the inlet valve is functioning correctly.

3. Error Code 9E

This error code is related to a low water level issue. It might occur if there’s a problem with the water supply or if the dishwasher’s float sensor is malfunctioning. Check to make sure the water supply to the dishwasher is adequate. If the water supply is not the issue, the float sensor inside the dishwasher might need to be cleaned or replaced.

4. Error Code LE

An LE error code indicates a leak detected by the dishwasher’s leak sensor. This is often situated at the base of the dishwasher. If there’s any water or moisture here, the LE code will display. To address this, check for leaks around the dishwasher, including hoses and connections. If no external leaks are found, the dishwasher might have internal issues that need professional attention.

5. Error Code OE

This code points to an overflow condition. It can happen if the dishwasher gets too much water or if the water fails to shut off properly. This might be related to a malfunctioning water inlet valve or a faulty float mechanism. Shut off the water supply and check these components for proper operation.

6. Error Code HE

The HE error code is related to heating issues. The dishwasher will display this code if it detects a problem with the heating element or if the water is not heating up as expected. This could be due to a malfunctioning heating element, a faulty thermostat, or issues with the control board.

7. Error Code CE/LE

This error indicates a motor operation issue, signifying that the motor is not functioning correctly. This could be due to a problem with the motor itself or with the wiring connected to the motor. Ensure all connections are secure and inspect the motor for any signs of damage.

8. Error Code tE1

This error indicates a problem with the dishwasher’s temperature sensor, also known as the thermistor. If the dishwasher is unable to accurately detect water temperature, it will display this code. To address this issue, check the thermistor for proper connection and functionality. It might need to be cleaned or replaced if found to be faulty.

9. Error Code bE2

The bE2 error code signifies a problem with the button on the control panel. It typically appears when a button is stuck or if the control panel is malfunctioning. Try to identify any buttons that may be stuck and attempt to free them. If the problem persists, the control panel might need to be repaired or replaced.

10. Error Code PE

This code indicates an issue with the half-load (or vario) motor, which is responsible for directing water to specific zones within the dishwasher. If the motor or its control circuit is faulty, the PE code will appear. Inspect the motor and its connections for any signs of damage or disconnection.

11. Error Code OE

This error code, not to be confused with the earlier mentioned OE (overflow condition), indicates a problem with the water level sensor. If the dishwasher is unable to correctly sense the water level, this code will be displayed. Check the sensor and its connections for any issues.

12. Error Code OC/0C

This code points to an over-level water error, which means the dishwasher is detecting too much water inside the unit. This could be due to a malfunctioning water inlet valve, a faulty water level sensor, or a problem with the control board. Verify that the water inlet valve closes properly and inspect the water level sensor for proper operation.

13. Error Code PC

The PC error code signifies a problem with the printed circuit board (PCB). This could be due to a communication error between the control panel and the main PCB or a fault within the PCB itself. Ensure all connections between the control panel and PCB are secure and intact. If the issue persists, the PCB may need professional inspection or replacement.

14. Error Code dE

This code indicates a door switch error, meaning the dishwasher is having trouble detecting if the door is closed properly. This could be due to a faulty door latch or switch. Ensure the door is closing securely and inspect the latch and switch for any damage or misalignment.

15. Error Code iE

The iE error code indicates an inlet error, which means the dishwasher is experiencing issues with the water supply. This could be due to low water pressure, a kinked supply hose, or a clogged inlet filter. Check the water supply to ensure it is adequate and inspect the inlet hose and filter for any obstructions.

16. Error Code uE

This code signifies an unbalance error, which is less common in dishwashers but can appear in models with load-sensing technologies. It indicates that the dishwasher is having trouble balancing the wash load, possibly due to uneven distribution of dishes. Rearrange the dishes to ensure even distribution and restart the cycle.

Conclusion

Samsung dishwasher error codes are designed to help you quickly identify and address issues with your appliance. By understanding what these codes mean, you can often troubleshoot and resolve simple problems without the need for professional help. However, if the issue persists or if you are unsure about performing any repairs, it’s always best to consult with a qualified technician to ensure the safety and longevity of your dishwasher. Regular maintenance and cleaning can also prevent many of these issues from occurring, ensuring your Samsung dishwasher continues to run efficiently for years to come.